Plan the display around the figure you actually ordered
The Hobbysakura Augusta 1/7 scale figure is a fixed-pose PVC and ABS display piece, not a toy you pose and rearrange. That single fact should drive most of your display and care decisions. Before you pick a shelf or clear a spot, check the supplied catalog details so your setup matches the figure’s real footprint and height.
The figure is listed at approximately H285mm, which is the number to use when checking shelf clearance and cabinet height. Because the supplied record does not include a base diameter or a depth measurement, leave extra room front-to-back rather than assuming the figure will sit flush against a back panel. If your shelf is tight, measure the space first and treat H285mm as the minimum vertical clearance, not the target.
Catalog details that affect display and handling
- [Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura: Material: PVC, ABS These are standard display-figure materials; they are rigid and detailed, so handle the figure by stable sections rather than thin or protruding parts.
![[Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura](/uploads/sites/2287/import-1786952909005-895823039.jpg)
[Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura - [Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura: Dimensions (approx.): H285mm Use this as your height check for shelves, cabinets and dust covers; the supplied record does not give width or depth.
- [Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura: Product Type: 1/7 Scale Figure A fixed scale display piece that is meant to be set up and left in place, not a poseable action figure.
- [Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura: Bonus: Badge*1 (58mm) The badge is a separate small item; store it away from the figure so it does not scratch the paint or get lost during cleaning.
A safe setup routine when the figure arrives
The supplied record does not include assembly instructions or a base description, so treat the following as general handling practice for a fixed PVC/ABS scale figure rather than a manufacturer procedure. If the packaging includes a printed instruction sheet, follow that first.
- Unbox on a soft, clear surface: Work over a clean cloth or a low-traffic table so small parts such as the badge do not roll away or get stepped on.
- Handle the figure by its stable body sections: Lift the figure from the torso or base area rather than pulling on hair, accessories or thin protrusions. Keep the badge separate from the figure during handling.
- Check the shelf before placing the figure: Confirm at least H285mm of vertical clearance and enough depth that the figure is not pressed against a back panel or door. The supplied record does not give a base footprint, so test the spot with the figure in hand before committing.
- Choose a stable, low-traffic location: A closed cabinet or a shelf away from walkways and door swings reduces the chance of knocks. Avoid spots where the figure could be hit by bags, pets or cleaning supplies.
Dusting without damaging paint or details
Dust is the main long-term issue for a displayed scale figure, but the fix is gentle and regular rather than aggressive. Start with a soft brush or a clean, dry microfiber cloth and work from the top down so dust does not settle onto areas you have already cleaned. Use light strokes around hair, clothing folds and any painted details; do not scrub or use pressure to remove stubborn dust.
The supplied record does not include cleaning instructions or approved cleaning products, so avoid guessing at solvents. Keep water, alcohol and household cleaners away from the figure unless the manufacturer’s own documentation says otherwise. For the 58mm badge, wipe it separately with a dry cloth and store it apart from the figure so the metal and pin do not contact the paint.
Display habits that protect a fixed scale figure
- Keep direct sun and heat away: A spot out of direct sunlight and away from radiators or heating vents is safer for painted PVC over time. The supplied record does not make a specific lightfastness claim, so treat this as sensible display practice.
- Leave breathing room around the figure: Do not press the figure against a back panel, shelf door or neighboring collectibles. The record gives height only, so check depth by eye with the figure in place.
- Secure the shelf if you display high: A high shelf reduces handling but increases fall risk. Use a stable shelf and keep the figure back from the edge; the supplied record does not include a base-locking feature or wall-mount hardware.
- Store the badge and packaging separately: Keep the 58mm badge and any packaging inserts in a small bag or box. Packaging is useful if you ever need to move the figure, and separating small items prevents scratches.
What the supplied information does not cover
The catalog record confirms the material, approximate height, scale, manufacturer and the included badge, but it does not include a base diameter, assembly steps, cleaning products, UV resistance or a weight rating. Those gaps are decision limits, not signs that the figure lacks a feature. If you need those specifics, check the manufacturer’s documentation or the figure’s packaging when it arrives.
This is also a pre-order item with a close date of 2026-08-30, a manufacturer release date of May-2027 and a US arrival of Sep-2027. Plan your display space for that timeline rather than clearing a shelf today, and keep the figure in its packaging until you have a stable, dust-controlled spot ready.


![[Pre-order] Wuthering Waves - Augusta 1/7 Scale Figure Hobbysakura](https://nekotwofgt.com/api/image-optimizer?src=%2Fuploads%2Fsites%2F2287%2Fimport-1786952909005-895823039.jpg&w=800&q=86)